Select the VPN client configuration files that correspond to the architecture of the Windows computer. You must have Administrator rights on the Windows client computer from which you want to connect. For the list of client operating systems that are supported, see the point-to-site section of the VPN Gateway FAQ. You can use the same VPN client configuration package on each Windows client computer, as long as the version matches the architecture for the client. If only SSTP is configured, then the Generic folder isn’t present. The Generic folder is provided if IKEv2 or SSTP+IKEv2 was configured on the gateway. Generic, which contains general information used to create your own VPN client configuration.The WindowsAmd64 installer package is for all supported 64-bit Windows clients, not just Amd. WindowsAmd64 and WindowsX86, which contain the Windows 64-bit and 32-bit installer packages, respectively.Unzip the configuration file to view the following folders: This configuration doesn't require additional client software. This section helps you configure the native VPN client on your Windows computer to connect to your VNet. The folders and files that the zip file contains depend on the settings that you selected when creating your P2S configuration. Generate the VPN client configuration files using the following command: $profile=New-AzVpnClientConfiguration -ResourceGroupName "TestRG" -Name "VNet1GW" -AuthenticationMethod "EapTls"Ĭopy the URL to your browser to download the zip file. When generating VPN client configuration files, the value for '-AuthenticationMethod' is 'EapTls'. The folders and files that the zip file contains depend on the settings that you selected when creating your P2S configuration.įor next steps, depending on your P2S configuration, go to one of the following sections: It's named the same name as your gateway. Once the configuration package has been generated, your browser indicates that a client configuration zip file is available. During this time, you may not see any indications until the packet has generated. It takes a few minutes for the client configuration package to generate. This doesn't download VPN client software, it generates the configuration package used to configure VPN clients. On the virtual network gateway page, select Point-to-site configuration to open the Point-to-site configuration page.Īt the top of the Point-to-site configuration page, select Download VPN client. In the Azure portal, navigate to the virtual network gateway for the VNet that you want to connect to. You can generate VPN client profile configuration files using PowerShell, or by using the Azure portal. The client certificate is installed in Current User\Personal\Certificates.Ģ. To view an installed client certificate, open Manage User Certificates.For information about client certificates, see Point-to site: generate certificates.The exported client certificate must be exported with the private key, and must contain all certificates in the certification path. A client certificate must be installed on each client computer. Install certificatesĪ client certificate is required for authentication when using the Azure certificate authentication type. If you're using TLS for point-to-site connections on Windows 7 and Windows 8 clients, see the VPN Gateway FAQ for update instructions. If you’re using TLS for point-to-site VPNs on Windows 10 or later clients, you don’t need to take any action. Only point-to-site connections are impacted site-to-site connections won't be affected. Starting July 1, 2018, support is being removed for TLS 1.0 and 1.1 from Azure VPN Gateway. Steps differ, depending on the authentication type, tunnel type, and the client OS. The following table shows the configuration articles available for Azure VPN Gateway P2S VPN clients. Before you beginīefore beginning, verify that you are on the correct article. For more information about P2S connections, see About point-to-site VPN. If there are any changes to the P2S VPN configuration after you generate the files, such as changes to the VPN protocol type or authentication type, you need to generate new VPN client configuration files and apply the new configuration to all of the VPN clients that you want to connect. The VPN client configuration files that you generate are specific to the P2S VPN gateway configuration for the VNet. The settings in the zip file help you easily configure the VPN clients. All of the necessary configuration settings for the VPN clients are contained in a VPN client configuration zip file. If you use the tunnel type OpenVPN, you also have the option of using the Azure VPN Client or the OpenVPN client software. When you connect to an Azure virtual network (VNet) using point-to-site (P2S) and certificate authentication, you can use the VPN client that is natively installed on the operating system from which you’re connecting.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |